Online client form
ECU Service Client Form
ECU services for engine-swap projects - not standard-vehicle modification
Close
Online client form
New Harness Build Client Form
Premium new standalone harness order - customer supplies ECU
Close
Leave this field empty
Submission verification
Enable JavaScript to complete verification, or contact sales@lexusv8.com.
Overview & Shipping
Available for selected manual-transmission 2UZ-FE and 3UZ-FE applications, subject to ECU and project review. Customer supplies the ECU unless otherwise quoted.
Shipping Address Lexus V8 Engines LLC 8124 Alfred Blvd Punta Gorda, Florida, USA 33982
Important shipping requirement: Do not use USPS because USPS does not deliver to this address. Ship with FedEx or UPS only.
Pack components securely with padding on all sides. Place this completed form or the printed summary inside the box so the parts can be matched to the job. Email your tracking number once shipped.
Required Components / Information
Customer-supplied ECU / ECM unless Lexus V8 Engines is supplying one Accelerator pedal and pedal plug where drive-by-wire is used MAF sensor and plug if not already confirmed Clear engine bay, ECU location, transmission, and recipient vehicle photos Printed copy of this completed form inside the shipment if components are shipped
What You'll Receive
Premium new standalone harness built for the selected application Client plug wiring references for vehicle-side connections ECU programming included as specified for the build where supported Immobilizer removal included where required and supported Bench/start-stand test video where applicable before invoice/shipment
Pricing Guide and Terms
New Standalone Harness - Manual Application $1,600 Includes premium new harness build, manual configuration, ECU flashing/programming, and immobilizer removal for customer-supplied ECU where supported.
Pre-programmed ECU Supplied by Lexus V8 +$120 Optional ECU supply where available and applicable.
Return Shipping Based on location Final return shipping is confirmed on the invoice before payment.
Pricing is a guide based on normal supported applications. Missing components, damaged parts, unsupported ECUs, custom wiring, additional connector replacement, repair, recovery, or special integration may change final pricing.
Workmanship is covered for the specific service performed unless otherwise stated in writing. Customer-supplied used electronics, sensors, pedals, connectors, and harnesses cannot be guaranteed against internal failure, prior damage, water intrusion, impact damage, unsupported variants, or previous modifications. Warranty is void if the ECU or harness is opened, cut, modified, tampered with, installed incorrectly, powered incorrectly, or used outside the intended application after service. Lexus V8 Engines LLC may request photos, videos, scan-tool data, voltage tests, ECU reads, or return inspection before determining the next step on any reported issue. The customer is responsible for final vehicle-side wiring, fusing, grounds, mounting, routing, and safe installation unless otherwise quoted in writing. Direct Deposit / Zelle has no fee. PayPal / card payment has a 3.5% processing fee. Payment is due upon invoice receipt before return shipment.
Complete your build details in order Donor = the vehicle the engine came from. Recipient = the vehicle you are building it into. Leave unknown optional details blank and explain them in Requested work.
Client details Donor engine and setup Recipient vehicle Requested work Harness layout and branch colour Additional contact notes Confirmation 1. Client details Who we should contact and where your completed parts would be returned.
Full Name * Phone Email * Preferred Contact Select one Email Phone WhatsApp Text message Street City State / Province ZIP / Postal Code Country Best Time To Contact
2. Donor engine and setup Tell us about the original engine, matching ECU and the gearbox you will use. This is not the recipient vehicle.
Engine Model Enter your engine model and variant, for example 3UZ-FE VVT-i or 2UZ-FE non-VVT-i. Include important engine changes. Donor vehicle Donor Year / Model The year and model the engine came from, for example 2003 Lexus LS430. Gearbox model Enter the gearbox model being fitted, for example Toyota R150F or A750F. Transmission type * Manual New harness builds are available for manual transmissions only. ECU case part number (89661-xxxxx) Copy the number from the ECU label. Leave blank if unknown; do not guess.
3. Recipient vehicle The vehicle receiving the engine.
Vehicle Receiving Engine The vehicle you are building, for example Toyota Hilux or Tacoma. Recipient year / model
4. Requested work Choose the work you want reviewed and describe the finished result. Final scope and pricing are confirmed by the workshop.
Requested work / project notes Include anything not covered above. Keep donor details and recipient-vehicle details separate.
5. Harness layout and branch colour Choose your loom finish and describe mounting, routing and installation requirements.
6. Additional contact notes Optional information to help us respond.
How did you hear about us? Preferred contact method Other contact notes
Build photos (optional) Clear photos help us confirm the ECU and understand the installation. These are shared privately with the workshop. JPG, PNG or WebP; up to 6 photos, 6 MB each and 18 MB combined. Please avoid including unrelated personal information.
ECU label Donor engine Harness / connectors Recipient engine bay
7. Confirmation Check the details above before signing and submitting the form.
Signature * Date * Printed Name Company / Shop if applicable
Agreement
By signing below, I confirm the new harness build requirements and acknowledge that final vehicle-side wiring, mounting, routing, fusing, and grounds remain the installer/customer responsibility unless quoted otherwise.
I have read and agree to the pricing, warranty limits, payment terms, and authorization statement above.
Send to Lexus V8 & Customer
Clear
A copy is emailed to Lexus V8 Engines LLC and to the customer email entered above. A printable box summary appears below after submit so the customer can include it with the shipped parts.
Online client form
Rebuilt Harness and ECU Client Form
OEM harness rebuild, standalone reconfigure, and ECU service
Close
Leave this field empty
Submission verification
Enable JavaScript to complete verification, or contact sales@lexusv8.com.
Overview & Shipping
MANUAL OR AUTOMATIC: For customers sending their ECU and OEM harness for rebuild/reconfigure.
Shipping Address Lexus V8 Engines LLC 8124 Alfred Blvd Punta Gorda, Florida, USA 33982
Important shipping requirement: Do not use USPS because USPS does not deliver to this address. Ship with FedEx or UPS only.
Pack components securely with padding on all sides. Place this completed form or the printed summary inside the box so the parts can be matched to the job. Email your tracking number once shipped.
Required Components / Information
Main engine harness Starter / knock-sensor sub-harness where separate ECU / ECM for programming or immobilizer removal Transfer-case actuator control unit and pigtail if transfer-case integration is required Accelerator pedal and pedal plug where drive-by-wire is used Any rear harness pigtail, speed sensor, reverse-light, or pass-through wiring required
What You'll Receive
OEM harness rebuild/refresh and standalone reconfiguration where applicable Connector/terminal/seal replacement as required and quoted ECU programming / immobilizer work selected and supported Bench/start-stand test video where applicable before invoice/shipment Client plug wiring references for vehicle-side connections
Pricing Guide and Terms
Standalone OEM Harness Rebuild $750 Base rebuilt standalone harness conversion. Includes immobilizer removal if required and supported by the ECU.
ECU Flashing Service $150 Required for supported calibration or application changes beyond base immobilizer/manual setup.
Throttle Response Tune Quoted after ECU/calibration review Scope and pricing depend on the supplied ECU and requested calibration changes.
Transmission Wiring $100 Additional automatic-transmission wiring where required.
Transfer Case Wiring $90 Additional transfer-case interface wiring where required.
Engine Connector Replacement $5 - $10 each Connector replacement where damaged, brittle, broken, oil-soaked, heat-damaged, or unsuitable for long-term use.
ECU Connector Replacement $12 - $40 each Varies depending on ECU connector type and application.
Return Shipping Based on location Final return shipping is confirmed on the invoice before payment.
Pricing is a guide based on normal supported applications. Missing components, damaged parts, unsupported ECUs, custom wiring, additional connector replacement, repair, recovery, or special integration may change final pricing.
Workmanship is covered for the specific service performed unless otherwise stated in writing. Customer-supplied used electronics, sensors, pedals, connectors, and harnesses cannot be guaranteed against internal failure, prior damage, water intrusion, impact damage, unsupported variants, or previous modifications. Warranty is void if the ECU or harness is opened, cut, modified, tampered with, installed incorrectly, powered incorrectly, or used outside the intended application after service. Lexus V8 Engines LLC may request photos, videos, scan-tool data, voltage tests, ECU reads, or return inspection before determining the next step on any reported issue. The customer is responsible for final vehicle-side wiring, fusing, grounds, mounting, routing, and safe installation unless otherwise quoted in writing. Direct Deposit / Zelle has no fee. PayPal / card payment has a 3.5% processing fee. Payment is due upon invoice receipt before return shipment.
Complete your build details in order Donor = the vehicle the engine came from. Recipient = the vehicle you are building it into. Leave unknown optional details blank and explain them in Requested work.
Client details Donor engine and setup Recipient vehicle Requested work Harness layout and branch colour Components being supplied Additional contact notes Confirmation 1. Client details Who we should contact and where your completed parts would be returned.
Full Name * Phone Email * Preferred Contact Select one Email Phone WhatsApp Text message Street City State / Province ZIP / Postal Code Country Best Time To Contact
2. Donor engine and setup Tell us about the original engine, matching ECU and the gearbox you will use. This is not the recipient vehicle.
Engine Model Enter your engine model and variant, for example 3UZ-FE VVT-i or 2UZ-FE non-VVT-i. Include important engine changes. Donor vehicle Donor Year / Model The year and model the engine came from, for example 2003 Lexus LS430. Gearbox model Enter the gearbox model being fitted, for example Toyota R150F or A750F. Transmission type Select one Manual Automatic Choose Manual or Automatic for the gearbox being fitted. ECU case part number (89661-xxxxx) Copy the number from the ECU label. Leave blank if unknown; do not guess.
3. Recipient vehicle The vehicle receiving the engine, plus the transfer case that will be used if applicable.
Vehicle Receiving Engine The vehicle you are building, for example Toyota Hilux or Tacoma. Recipient year / model Transfer case integration Select one Yes No Unsure Transfer case being used
4. Requested work Choose the work you want reviewed and describe the finished result. Final scope and pricing are confirmed by the workshop.
Required ECU Work Required Harness Work Requested work / project notes Include anything not covered above. Keep donor details and recipient-vehicle details separate. Immobilizer Delete ECU Flashing Service Throttle Response Tune Automatic Transmission Wiring Transfer Case Wiring Cruise Control Required Manual Pass-Through Pigtail OBD2 Port Required A/C Control Wire Customer Notes / Requested Details
5. Harness layout and branch colour Choose your loom finish and describe mounting, routing and installation requirements.
Harness Condition Notes Harness branch colour preference Select one Black/Blue Black/Red Black/Green Black/Black Choose Black/Blue, Black/Red, Black/Green or Black/Black. This is a preference; we confirm the final loom finish with you. Branch colour photo guide Click a photo to select that branch colour, or use the dropdown above. Use View larger to inspect the sleeve. Supplier photos are visual references; colour and weave appearance can vary with sleeve diameter, lighting and your screen.
A/C Required Select one Yes No Unsure A/C installation details 6. Components being supplied Select only the items you will send us. Describe any additional components in your project notes.
Main engine harness Starter / knock sensor sub-harness ECU Transfer case control unit + pigtail Rear-harness pigtail / speed sensor / reverse lights Other
7. Additional contact notes Optional information to help us respond.
How did you hear about us? Preferred contact method Other contact notes
Build photos (optional) Clear photos help us confirm the ECU and understand the installation. These are shared privately with the workshop. JPG, PNG or WebP; up to 6 photos, 6 MB each and 18 MB combined. Please avoid including unrelated personal information.
ECU label Donor engine Harness / connectors Recipient engine bay
8. Confirmation Check the details above before signing and submitting the form.
Signature * Date * Printed Name Company / Shop if applicable
Agreement
By signing below, I confirm the rebuilt harness and ECU service selections and acknowledge that connector condition, missing components, and unsupported ECU variants may affect final pricing.
I have read and agree to the pricing, warranty limits, payment terms, and authorization statement above.
Send to Lexus V8 & Customer
Clear
A copy is emailed to Lexus V8 Engines LLC and to the customer email entered above. A printable box summary appears below after submit so the customer can include it with the shipped parts.
Custom application and compliance review Our services are built for purpose-designed dune buggies, rock crawlers, off-highway safari vehicles, closed-course race cars, boats and custom bikes. They are not offered for vehicles registered, licensed or intended for street or highway use.
This application restriction does not authorize emissions tampering. We do not offer or support calibrations that disable emissions-control or OBD functions on EPA-certified vehicles or engines. Every project is reviewed for its original certification, finished-machine classification, intended use and applicable federal, state and local requirements before acceptance.
Tell us about the complete application so the workshop can confirm whether it is eligible before parts are shipped.