A new standalone harness is prepared for a 1986 Toyota 4Runner with a 3UZ-FE and manual gearbox. The workshop video covers the wiring package and live test of the supplied engine-management system.
A 2003 2UZ-FE donor system is prepared for a 1989 Toyota 4Runner with an R150 manual gearbox. This workshop video documents the swap-wiring package and its engine-management connections.
A rebuilt 2UZ V8 wiring package is prepared for a 1994 Toyota Land Cruiser four-wheel-drive swap. The workshop video follows the harness walkthrough and test run for the supplied system.
A 1995 Lexus SC400 3UZ-FE manual conversion is documented with a full harness walkthrough and workshop test run. The video shows the supplied engine-management package for this particular swap.
Jason’s 1986 Toyota Hilux YN67 4WD is being prepared for a 3UZ-FE V8 from a 2005 Toyota Crown UZS186 with a Toyota R150F manual transmission. This workshop video documents the standalone wiring harness build, ECU integration and live test verification.
A 1981 Toyota Land Cruiser FJ40 receives a 2UZ-FE manual-swap wiring package. This workshop walkthrough documents the harness and engine-management connections and the test run shown for the supplied setup.
A 1990 Toyota Hilux 2UZ-FE manual swap uses a new right-hand-drive harness. This video reviews the harness layout and connections, followed by the workshop test run shown for that package.
This 1991 Toyota 4Runner 2UZ-FE manual-swap project is documented through its harness and ECU workshop test. The video records the supplied wiring package and engine-management verification.
A 2006 Toyota 4Runner 4.7L 2UZ-FE VVT-i engine, automatic transmission and 4x4 transfer-case wiring package is prepared for a 1992 Toyota Land Cruiser. The walkthrough covers the completed standalone harness, automatic and four-wheel-drive interfaces, OBD-II verification and successful test run.
A walkthrough of the wiring package prepared for a 1997 Lexus LX450 receiving a non-VVT 2UZ-FE with an automatic transmission. It documents the rebuilt harness, vehicle interfaces, ECU and diagnostic connections, and test-stand checks.
A 2000 Land Cruiser 2UZ-FE and A343F package is prepared for a 1994 FZJ80 conversion. The video covers the standalone harness layout, vehicle connections, and bench-test setup.
A 2006 LS430 3UZ-FE VVT-i and six-speed automatic package is configured for a 1990 Toyota Hilux Surf. The walkthrough covers the standalone harness, ECU integration, and live test.
This walkthrough covers a 2004 Toyota Tundra 2UZ-FE automatic 2WD configuration. It shows the finished harness, fuse and relay center, vehicle-side connections, retained A/C interface, and test run.
A technical walkthrough of reconfigured 3UZ-FE engine-management wiring with a six-speed automatic transmission and transfer-case interface. The video documents the harness layout, control connections, and test run.
A 2UZ-FE automatic 4x4 wiring package is prepared for a 1996 Land Cruiser 80 Series using a 1999 Land Cruiser donor system. The video covers the rebuilt harness, ECU connections, and test verification.
A 2003 non-VVT 2UZ-FE, factory automatic transmission, and electronic transfer-case system are configured for a 1997 Toyota 4Runner. The video shows the completed wiring package and test run.
A 2UZ-FE, A750F automatic transmission, and HF2AV transfer-case wiring package is prepared for a 1991 Toyota FJ80. The video reviews the harness interfaces and test-stand verification.
This video documents a rebuilt and reconfigured 3UZ-FE manual standalone harness. It covers engine-side routing, ECU setup, vehicle-side connections, and the completed test run.
A non-VVT 2UZ-FE automatic 4x4 harness from a 2002 Toyota Sequoia is prepared with cruise-control integration. The walkthrough shows the harness layout, ECU and vehicle interfaces, diagnostics, and test run.
A new 3UZ-FE VVT-i standalone harness is built in manual configuration for a 1972 Toyota Land Cruiser FJ55. The walkthrough covers the cab-mounted ECU layout, harness connections, and test run.
A 2UZ-FE VVT-i automatic wiring package is prepared for a 2006 Toyota Tacoma. The video covers transmission control, transfer-case and front differential-locker interfaces, cruise control, harness connections, and test verification.
A 2005 Tundra 2UZ-FE VVT-i and A750E wiring package is prepared for a 1972 Toyota FJ40 conversion. The video documents the harness, ECU preparation, transmission interface, and test run.
A new 3UZ-FE standalone harness is built in manual configuration for a 2013 Scion FRS. The video reviews the engine-side layout, ECU and vehicle connections, relay and fuse arrangement, and test run.
A 3UZ-FE manual-swap wiring package is configured for a Toyota Tacoma. The walkthrough covers the standalone harness, ECU setup, throttle-pedal and OBD-II connections, vehicle interface, and test run.
This video reviews a 3UZ-FE six-speed standalone wiring package. It shows the harness layout, ECU, relay and fuse arrangement, vehicle-side plug, accelerator-pedal connection, and engine test run.
A GS400 1UZ-FE VVT-i system is prepared for a 2003 Lexus IS300 manual conversion. The video documents the harness conversion, ECU preparation, vehicle interfaces, and test-stand verification.
A factory 3UZ-FE harness is prepared as a standalone system with five-speed automatic transmission control. The walkthrough covers the ECU, fuse and relay arrangement, vehicle connections, and test run.
A 2002 Sequoia non-VVT 2UZ-FE automatic 4x4 harness is reworked for an 80 Series Land Cruiser conversion. The video covers the standalone layout, transfer-case actuator interface, and completed test run.
This technical explanation covers a 2UZ-FE manual standalone wiring system. It shows how the engine-management circuits, ECU, power distribution, and vehicle-side connections are organized.
A completed 2UZ-FE VVT-i engine-management package is configured for a manual conversion. The video reviews the harness layout, ECU and vehicle connections, diagnostics, and live test.
A 3UZ-FE VVT-i six-speed automatic wiring package is prepared for a 2013 Mazda BT-50 2WD project. The walkthrough covers the harness, ECU preparation, transmission interface, and test-stand verification.
A new 3UZ-FE VVT-i standalone wiring package is prepared for a 1992 Toyota 4Runner 4x4 with a manual transmission. The video documents the harness layout, ECU and vehicle interfaces, and test verification.
A 2003 SC430 3UZ-FE VVT-i system is prepared for a 1981 Toyota Pickup 4x4 with a manual transmission. The video covers the harness rebuild, ECU preparation, vehicle connections, and test-stand verification.
A 2000 LS400 1UZ-FE VVT-i engine and ECU package is prepared for a 1996 Toyota Tacoma 2WD with a manual transmission. The video documents the rebuilt harness, vehicle interfaces, and OBD-II test.
A 100 Series Land Cruiser 2UZ-FE drivetrain is prepared for an 80 Series Land Cruiser conversion. The video reviews the drivetrain configuration, standalone wiring preparation, ECU integration, and vehicle interfaces.
A 2006 SC430 3UZ-FE VVT-i system is prepared for a 1990 Toyota Supra A70 with a manual transmission. The video covers the rebuilt conversion harness, cruise-control interface, and test verification.
This walkthrough covers a new 3UZ-FE standalone swap harness and its fuse and relay center. The video documents the supplied connections, live test run, and OBD-II diagnostic scan.
A Toyota 2UZ-FE package is configured for a manual-transmission conversion using a 2001-2002 Sequoia ECU. The walkthrough covers the completed wiring, vehicle interfaces, ECU preparation, and test run.
A 2UZ-FE wiring package is prepared for a 1995 Toyota T100 4x4 with an R150 manual transmission. The video reviews the engine and vehicle connections, power distribution, diagnostics, and test verification.
A custom 3UZ-FE standalone wiring package is configured for a left-hand-drive manual conversion with the ECU mounted inside the cab. The video shows the harness layout, vehicle interfaces, and test-stand verification.
A 3UZ-FE wiring package is prepared for a 2001 Toyota 4Runner with a five-speed manual transmission and retained factory cruise control. The video covers the vehicle interfaces and test verification.
A 3UZ-FE VVT-i wiring package is prepared for a 2013 Scion FRS drift build with a six-speed manual gearbox. The video documents the standalone harness, vehicle connections, and test proof.
This installation guide shows the engine-side connection of a custom 3UZ-FE standalone harness. It covers plug locations, harness routing, and securing the wiring on the engine.